image40

Extreme Hand Protection

Learn More

 Glove Pictured above

 Banom®  SteelGard® 

Find out more

About Us

image41

BBP-8305

 Terminator® - MaxPly® Dyneema® with Polyurethane Palm Coating - ANSI/ISEA 105-2016 Cut Level A2, EN 388 - 4342 

 Terminator® cut resistant gloves are soft, durable, cool, and  comfortable to wear. These gloves have proven to be safe and cost  effective in sheet metal and electrical assembly operations where  dexterity is required.  

image42

BBP-1905

 MetalMaster® - Dynamax® HD with Polyurethane Palm Coating -ANSI/ISEA 105-2016 Cut Level A2, EN388 4343 

 MetalMaster® gloves were specifically designed for lean manufacturing  where a broad range of tasks are performed by the same set of hands.  MetalMaster® gloves are made with Dynamax® HD, a lightweight continuous  filament yarn that works on a principle of ultra high tensile strength  to provide cut resistance in sheet metal applications. 

image43

BBP-6505

 Flex4® -Polyurethane Palm Coating on Dynamax®45 Liner - ANSI/ISEA 105-2016 Cut Level A4, EN 388 4542

 Flex4® gloves are designed for use in sheet metal and knife blade  hazards where the edges are sharp. As sheet metal gets thinner, the  edges become sharper and the burrs much smaller. In these situations, a  glove must have both tensile strength and yarn hardness. Applications  include paper mills, corrugated manufacturing, plastic mold trimming,  carpet cutting, and can manufacturing. Flex4® gloves are made with  Dynamax® 45, which combines ultra high tensile strength with a yarn  hardness that allows this product to resist the cutting edges of sheet  metal, machined metal, glass, and knife blades.  

image44

BBP-7205 - Banom®SteelGard®

 Cut Test Data:        ANSI/ISEA 105-2016 Cut Level A9

These gloves are knit with two strands of cut resistant composite yarn.  If one strand fails, the other acts as a back up. SteelGard® gloves are  100% latex free. Taperfit® cuffs are extended length to protect the  wrist area. These gloves contain AlphaSan® which prevents bacteria from  growing both during and after glove use. SteelGard® gloves are made  entirely of FDA accepted materials required by USDA for food use. 

 Cautions:        This product contains stainless steel, which can make the user potentially conductive in an electrical hazard situation.   

image45

BBP-5205 Banom®Dominator®

Banom®Dominator® RTC - Dynamax® HD with Foam Nitrile Coating - ANSI/ISEA 105-2016 Cut Level A2
  Dominator® RTC gloves offer the same protection as the regular  Dominator® gloves but with the added benefit of a reinforced thumb  crotch. These gloves provide liquid protection from non-hazardous  chemicals in environments where cut resistance from machined parts or  metal edges is required. This coating offers additional wear resistance  without restricting flexibility. Dominator® RTC gloves are made with  Dynamax® HD, a lightweight continuous filament yarn that works on a  principle of ultra high tensile strength to prevent a metal edge from  cutting into the fabric of the glove. Due to Banom's patented yarn  construction, these gloves are extremely light weight and provide  dexterity and tactile feel. Dominator® RTC gloves are 100% latex free  and are treated with Sanifresh® to keep bacteria from growing both  during and after glove use. The new Taperfit® knitwrist cuffs are  extended length to protect the wrist area without causing tightness or  discomfort. Due to their tacky grip, Dominator® RTC gloves are not  recommended for use when turning nuts, bolts, or screws with a power  tool as this can result in a “wrap-up”. Nitrile coatings can become  slippery in water-based solutions. These gloves are made with a  synthetic yarn, so they should not be used near heat or open flame.  Dominator® RTC gloves should be edge-tested prior to approval for use